(Solved) Why Is My New Hot Water Heater Not Working Tutorial

Home > Water Heater > Why Is My New Hot Water Heater Not Working

Why Is My New Hot Water Heater Not Working

Contents

Teresa I have hot water but no hot water pressure. I believe The temperature was set too high. Hot low pressure. If you check between those two wires, you should have 240 volts assuming the bottom of the tank is cold. navigate here

turned the water off and running water sound stopped and so did the leaking. Don Vandervort, HomeTips If the burner is working properly, it should take a few hours, depending upon its size. This all started happening over the last weekend. Janice Grahovac It is gas shadow1458 Replaced the thermocoupler, lit the pilot, the burner came on then went out after a few seconds. have a peek at this web-site

Gas Water Heater Not Working

A5: A 4500 watt WH element is 12.8 ohms whether it is new or 20 years old, whether it is clean or scaled up. Steve Price I have a gas water heater. This will help some, but also uses more energy.

Gas Water Heater Doesn't Heat If a gas water heater fails to heat water at all, perform these diagnostics: 1Be sure the gas to the water heater is turned on. I am contemplating installing a thermal expansion tank. The leaking water likely caused a thermostat to malfunction too. How To Tell If Electric Water Heater Is Working Replace if you find either of these.

I lowered the pressure releaf tank pressure to match the city water pressure. Electric Water Heater No Hot Water Make sure the tester is working by putting the tip into an outlet you know has power. There are breakers made to fit the screw in type fuse holders. http://www.doityourself.com/forum/water-heaters/343419-installed-new-electric-water-heater-not-working.html As you will see in that article, relighting a water heater usually involves turning the water heater's gas valve to OFF and then to PILOT.

Carl Dunkin try opening and closing the shutoff valves under your sinks or it could be in the faucet itself hard water causes a chemical buildup in pipes etc. Electric Water Heater Thermostat minimise What do I do if my water heater is leaking? Your results seem to indicate a good thermostat. Plumberologist 518,651 views 5:36 Change a hot water heater element without draining or spilling water - Duration: 3:25.

  1. Get a Water Heater Repair Pro Fast!
  2. If it's good, you're getting a half tank of hot water.
  3. Lift or lower its handle.
  4. If your old element was caked with minerals, replace it with a low-density element for more efficient operation and longer life.

    Back to Top Video: How to Test Your Water
  5. Leaking fittings can often be tightened or repaired.
  6. You will need to contact your local plumber or hot water specialist for a replacement quote or call Rheem Service on 131 031 for advice on the appropriate replacement model minimise

Electric Water Heater No Hot Water

Janice Grahovac I will be checking those. read this post here Turn the gas valve control to OFF (you may have to push down to turn it). Gas Water Heater Not Working Why is it that this hot water isn't making it to the faucets? My Water Heater Is Not Heating Water If the fuse/breaker overheated that much, replace it.

Also make sure the water heater isn’t leaking. check over here You don’t have to drain the tank to replace a thermostat. To replace an element, start by draining the tank. Verify your water heater is getting the correct voltage. Water Heater Reset Button

To expose the elements for testing, remove the two metal covers, the insulation and the plastic covers on the side of the water heater. Before you test the elements, check to make sure the circuit breaker is on and not tripped. brandy My gas water heater is lit but I have no hot water warren Check to see if water is getting to tank. his comment is here Call 1300 556 036 minimise How to relight a Rheem 4 Star Gas Water Heater minimise Water temperature not right?

Seems like it should be working. Electric Hot Water Heater Not Working After Power Outage If you are not familiar with electricity and testing devices GO NO FURTHER. This Old House 76,623 views 4:47 How to Know if a Hot Water Heater Element Needs to Be Replaced : Water Heaters - Duration: 2:04.

karen Oil heated hot water furnance is making hot water and comes on when desired but is not heating the home.

To post questions, help other DIYers and reduce advertising (like the one on your left), join our DIY community. Then install the new element, using the wrench to tighten it, and reconnect the wires (Photo 5). Also, every time you inspect an element port, put everything back the way you found it. Whirlpool Electric Water Heater Troubleshooting Thermal Expansion Tank When water is heated, it expands.

We’ll show you how to test the heating elements, remove one if it’s bad, and install a new one. Don Vandervort, HomeTips It usually means the burner isn't working. SIGN UP Invalid e-mail Advertise with us ADVERTISEMENT Follow Us Advertise with us ADVERTISEMENT Advertise with us ADVERTISEMENT We Recommend 20 Secret Hiding Places Save Money With Home Energy Audit Install http://codebuz.com/water-heater/water-heater-rv-not-working.html Category Howto & Style License Standard YouTube License Show more Show less Loading...

Touching the end of each wire to a continuous circuit will cause the bulb to light. Test both hot wires. steven lavimoniere 38,011 views 18:34 What do I do when my water heater is leaking? - Duration: 5:36. The purpose of the upper element is to provide quicker hot water and perhaps to give a little redundancy so that one doesn't completely run out of hot water should the

The upper element was toast. Of course the other (non-thermostat) side of each element is always hot. -- David A7 : You say a normal fast-acting 30 amp fuse blows in 3-4 minutes. When I flush my toilet on the opposite end of the house I hear water running at the heater until the toilet shuts off. Is the electricity switched on?- Check the isolating switch (typically located at the switchboard) and next to the water heater (if installed) are both turned on- Check the fuse marked “HOT

If you smell a garlic-like scent, turn the gas valve control to OFF (you may have to push down to turn it). Low gas pressure or a malfunctioning gas control valve could also cause a pilot light to go out repeatedly. You'll need a multimeter for this. The upper left and lower right terminal measured 0 ohms and when I adjusted the thermostat dial to maximum these measurements didn't change.

Mine is a safety that is under the burner that went out. Tighten water flex line.