Repair Water Heater Piezo Igniter Not Working (Solved)

Home > Water Heater > Water Heater Piezo Igniter Not Working

Water Heater Piezo Igniter Not Working

Contents

NOTE: On the Robertshaw gas control valve/thermostat the knob stop must first be depressed before turning the gas control knob. Use your smart phone to take a picture of the model number tag. Reply With Quote June 2nd, 2011,08:40 PM #8 weatie View Profile View Forum Posts Member Join Date Jun 2011 Location NJ Posts 4 He was able to get it going. There are a number of other possibilities to consider. have a peek at this web-site

To prevent problems with the water heater pilot light, it is crucial that you read the manufacturer instructions carefully; how to maintain gas water heaters and how to light it. Working... James Yuan 46,082 views 2:43 How to check and light water heater pilot light - Duration: 1:51. Refer to the section of "Draining and Flushing" section and follow the procedure.5.

Water Heater Igniter Not Sparking

Add to Want to watch this again later? A prolific carpenter, home renovator and furniture restorer, Deziel has been active in the building and home design trades since 1975. Its an A.O. They usually are hidden behind metal plates you can pry off with a screwdriver.

This is what I opted to do to fix my situation and I do not recommend you follow these actions if you are not familiar with basic HVAC controls. The air present in gas line could prevent the pilot light from lighting. A down draft from the ceiling fan or if there is a draft at the bottom of the unit, can blow out the pilot also. Piezo Igniter Won't Spark Smith Water Heater Water Heater A.O.

Please try the request again. Smith Hybrid ElectricHeat Pump Water Heater Manual Hybrid electric heat pump water heater (20 pages) Water Heater A.O. That being the case, how do I clear the line? http://www.thetankatwaterheaterrescue.com/forums/forum3/3674.html Smith RESIDENTIAL GAS WATER HEATER Instruction Manual A.o.

IMPORTANT: All leaks must be fixed immediately. 10. Water Heater Igniter Doesn't Work Jimmy946518 210,486 views 3:10 The majority of problems on todays water heaters can be solved with the tightspot vacuum brush. - Duration: 3:11. Smith GAS WATER HEATER DIRECT VENTED GAS MODELS Piezoelectric Igniter System A.O. Basically....

  1. Replace the outer door.DOOR GASKETFLAMEARRESTOR BRACKETTIP FIGURE 30.MANIFOLD TUBECLOSE-UP INSIDE VIEW OFTHE COMBUSTION CHAMBER.l BRACKETFIGURE 31.
  2. The spark electrode sends intermittent high-voltage sparks to light the pilot.
  3. Make sure the electrode is not broken...

Water Heater Igniter Not Working

If the spark electrode won’t produce sparks, it is likely defective. Hide thumbs 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Water Heater Igniter Not Sparking Your model number is on a plate, in one of these locations: Handy tip -Make it easy on yourself! Water Heater Piezo Igniter Won't Light All rights reserved.

Sign up! Check This Out Yes, some take longer than normal. Damage to the gas control valve/thermostat may result.28 × Show quick links Table of Contents PiezoelectricIgniterSystem TestingTheIgniterSystem Previous page Next page 1...242526272829303132 Related Manuals for A.O. lol.... Water Heater Pilot Won't Spark

State select water heater piezo igniter won't light HELP! Sign in Transcript Statistics 551,055 views 1,289 Like this video? Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up & Source All rights reserved.

Bubbles forming indicate a leak. Hot Water Heater Pilot Won't Light If the igniter is getting voltage, but it doesn’t glow, this indicates that the igniter is defective and should be replaced. Use only factory authorized piezoelectric igniter parts for replacement.IGNITER BUTTON-WIRE /TO ELECTRODESNAP-ON CONNECTORTHERMOCOUPLE /2P,LOT /PILOT _\ TIPBRACKET/.

Remind me later Review A privacy reminder from YouTube, a Google company Skip navigation GBUploadSign inSearch Loading...

Snap a new thermostat in place and reconnect the wires. Use your smart phone to take a picture of the model number tag. Otherwise, if the pilot light is not functioning properly, you won't have hot water. Electronic Ignition Water Heater Won't Light I have no spark either.

Before performing any maintenance, it is important to turn the temperaturedial on the gas control valve/thermostat toits lowest setting. 3.On top of the gas control valve/thermostat turn the gas control knob Each element is connected to a thermostat located just above or below it. 3Press the red reset button on the top thermostat if the circuit breaker is on but the heater gas systems use reverse (left-hand) threads on the manifold tube., ,Refer to "Gas Piping" section (Figure 3) and disconnect the ground joint union in the gas piping. have a peek here A visible spark should jump from the electrode.

ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection to 0.0.0.10 failed. Loading... Disconnect the thermocouple (right-hand threads), pilot tube, and manifold tube at the gas control valve/thermostat (Figure 22). Another reason is the wrong size of the pilot burner orifice.

You can change this preference below. There may be one located near the bottom of the heater, or two: one at the bottom and one at the top. Loading... Note that most of the older and economy gas water heaters are equipped with the pilot, while newer advanced models utilize a hot surface igniter which is more durable and reliable.

When I tried your slower method, it started up almost right away. Smith Manuals Water Heater Water Heater User manual A.O. If you have the wrong pilot burner replace it with the correct one. Get more answers from the people in your networks Tags Kenmore , Building Supplies Click to remove this tagging.

If no spark is visible, check the wire connections and make sure the electrode is not broken. While continuing to hold down the pilot button press down on the igniter button three or four times. Once pressed, the electrode should release the spark. Thanks In adavnce Weatie Reply With Quote June 2nd, 2011,04:12 PM #4 Icehouse View Profile View Forum Posts Visit Homepage HVAC Tech Join Date Nov 2008 Location Middle Island ,LI, NY

Youtube Icon Facebook Icon Twitter Icon Terms of SaleTerms of UsePrivacy Policy Need Help? Watch the electrode tip while activating the igniter. Dirt and rust on the pilot or electrode tip can prevent the igniter spark. Is there a way that I can check if the igniter system is working properly?

If the pilot is restricted, try removing it and clearing it with a stiff brush and/or compressed air.