I can not pass the suggested nylon line or even fin gauge wire more than 3-4 inches into the output nozzle. Loading... Cancel Maxxi Rep: 1 Posted: 07/21/2014 Options Permalink History Ge Ge what a nice machine pity it taken me months to find someone to fix this useless piece of you know Name (Required) Mail (will not be published) (Required) Website Recent Posts LG Refrigerator Change Water Filter Light On? have a peek at this web-site
You can confirm this by trying to insert a zip tie (8-10″ long) fully in to the water dispenser line (where the water normally comes out). I believe I packed the lower trays of my freezer to full and this caused the freeze up. Yes No Voted Undo Score 1 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? See if this may reset the fridge to get the display working again. -RRReply 84 rich December 2, 2015 at 3:00 pmI have a Frigidaire and after about 3 months of http://www.repairclinic.com/RepairHelp/How-To-Fix-A-Refrigerator/52---/Refrigerator-water-dispenser-not-working
Yes, the new refrigerators have a filter inside but I would rather keep the filter outside as the outside filter only costs $15 versus the "inside" filter costs $55-65. Was this answer helpful? Can main electronic board malfunction like that and still operate the fridge?Reply 7 Dana August 15, 2016 at 5:19 pmI have this EXACT same problem, however mine is a Kenmore fridge. It took about 5 minutes then waited about two more, waterline started to drip, from the melting and then it worked.
According to the directions, I began to drain 4 gallons of water, one gallon at a time. The hair dryer was on the door for 10 minutes. If you have verified that the water inlet valve is getting power and the actuator and switch are operating properly, then you may have a defective electronic control. 5 Gallon Water Dispenser Not Working Could I have an air lock in the line?Reply 89 DIY Project Help Tips December 1, 2015 at 8:32 pmJerry, Which valve are you referring to?
Thanks!!! Frigidaire Refrigerator Water Dispenser Not Working Add to Want to watch this again later? Use your smart phone to take a picture of the model number tag.
The water is making a bad humming noise and the water is barely flowing out .
But the water and ice won't dispense and the light won't come on. Ge Refrigerator Water Dispenser Not Working After Replacing Filter Ugggg…. No damage to door. Your GE fridge should have a microswitch that triggers the water flow when a cup or glass is depressed to it.
It's worked for more than a week in the new location, so that seems unlikely. Our door water hasn't worked in a year but the ice worked fine. Whirlpool Refrigerator Water Dispenser Not Working RepairClinic.com 267,406 views 3:59 Troubleshooting a GE water dispenser and installing a GE heater element - Duration: 58:13. Kenmore Elite Refrigerator Water Dispenser Not Working It is too much of a coincidence that the dispenser stopped working after filter change that a switch is the problem. -RRReply 106 Keith November 1, 2015 at 5:02 pmI have
Did you figure it out? http://codebuz.com/not-working/water-dispenser-for-fridge-not-working.html Have you made sure the valve that supplies water to the fridge is actually supplying water? The water inlet valve supplies water to the water dispenser. Refrigerator Water Dispenser Not Working After Filter Change Fridge not dispensing water after new filter change? Ge Refrigerator Water And Ice Dispenser Not Working
Main boards can be found at AppliancePartsPros.com. Didn't make a difference Then I tried the 10 minute blowdryer on the top half of the freezer door method, no change. Reply Ray August 29, 2015 at 4:26 pm # I used the hair dryer but didn't have any weed whacker cord so I used an 8″tie wrap to push into the Source I've been trying to figure this out!
Done ! Ge Refrigerator Water Frozen Try what we suggested before and if that does not work, take a look at the valve and be sure the water lines are secure as sometimes when water if pumped Reply Michael June 24, 2015 at 1:59 am # This worked perfectly!
http://www.graceappliance.com/IceSurrend... I had tried blow drying inside and in the spout before. If you're not able to do so - you have confirmed that you have ice blocking the water from flowing freely.Reply 39 Jack March 13, 2016 at 4:43 amI have a Ge Refrigerator Water Dispenser Not Working But Ice Maker Is It's actually inside the cabinet frame of which can not been seen.
It will take a little time, but it really does work. Heated front and back of center door but water didn't flow until I followed advice of earlier poster who put the hear at the bottom of the door where tube flows Help would be great. have a peek here Parts Dispenser Switch Please enter your model number so we can show you the part that fits your exact model Where is my model number?
Yes No Voted Undo Score 0 Cancel Comments: If you have tried changing micro switch at the water dispenser and changed the circuit board, and still not working then u have So I originally didn't think it worked. No controls for the fridge have been adjusted (including the temperature for fridge and freezer). THANKS!
Was this answer helpful? Skip navigation UploadSign inSearch Loading... Reply Colleen January 14, 2015 at 2:58 pm # If you call GE, at 1-800-386-1215 Opt. 6, you can get the part free of charge, or at least I did anyway. I have changed the filter by putting a brand new one in and it just shoots water out at a normal rate for about 2-3 seconds then slowly comes to a
Yes No Voted Undo Score 0 Cancel Comments: I have a GE refrigerator 15 years old, not making ice, I put a new water valve on and jump tested it and Cancel Add your answer john will be eternally grateful. The unit will be 8 years old this June. 02/25/2015 by JP THANK YOU! The water inlet valve requires a minimum of 20 psi to function properly.
All of a sudden, water and ice aren't being dispensed. The next day I called again and told them it didn't work. If the filter is too tight or too loose it may not dispense water properly. After thawing the line with a heater & lowering freezer setting to 1, the extra insulation works well & cost is minimal. ( not too pretty, but works ) Reply Carlos