Fix Whirlpool Ice Maker Not Working Infrared (Solved)

Home > Ice Maker > Whirlpool Ice Maker Not Working Infrared

Whirlpool Ice Maker Not Working Infrared

Contents

When I look at the optics beam hole on the left side I do not see any flashing lights, does that mean the control boards are bad or is it the Insert the jumper from T to H and close the door. See the description below at "Another issue with these ice makers involves replacing a part within the ice maker" (click here to go there) The instructions for replacing the optic boards Open the Freezer door for and activate the freezer door switch 3 times within 10 seconds (see Figure 6 above). 6. http://codebuz.com/ice-maker/whirlpool-infrared-ice-maker-not-working.html

The ice make will fill when the fingers that scoop the ice out are pointing straight up. I cannot tell you how happy I was- we had ice!!I just want to thank you (as does my husband) for the information that you made available- the illustrations, the step-by-step Now before you proceed, look in the ice mold (where the ice forms). When I look at the optic board, I do not see any light at all.

Whirlpool Ice Maker Reset Button

MAKE SURE YOUR EMAIL IS CURRENT AND CORRECT IN PAYPAL TO AVOID DELAY ON DELIVERY OF YOUR LOGIN AND PASSWORD. If the ice maker optic control boards fail, it can cause the ice maker to continue to make ice even when it is full of ice or turned off, or it To be sure I did not have a bad new board, I ordered another emitter set and still no lights on the emitter or power to the icemaker. - Where does

Reply DN Posted on April 25, 2015 Yep, that is what it was and replaced with a new or rebuilt one that my repair man had. That's the 2 o'clock position from the right side of the so-called fridge, not sure which orientation is meant by 2 o'clock. Please don't tell me that the ice maker itself is now broken. Whirlpool Conquest Ice Maker Parts I recommend making your appliance parts purchases from them.

Open the freezer door and remove the ice bin from the door...hopefully you can just set this aside for a few minutes while we complete this quick test on the optic Whirlpool Conquest Ice Maker Not Dispensing Ice It is pretty easy to check to see if the optic boards are working (and just as easy to fix the problem with these instructions and the proper parts). Now I have solid light with left flap manually held flat (stimulating an empty bin) and then flashing twice when the optics blocked (simulating a full bin). see this Reply Ryan Posted on June 11, 2015 Please post your question on our repair forums with your refrigerators model number and we can try to help you with this.

As I explained to you I had the ice maker out of my freezer in literally 5 minutes and taken apart in another 5. W10757851 I did the repair right before bed so I didn't get to hear the first batch of ice drop, but it was great to wake up this morning and look in Is that correct? Find your part: When repairing icemakers it is important to know how much ice the icemaker should produce.

Whirlpool Conquest Ice Maker Not Dispensing Ice

The ice maker is doing its 'clunking', what a great sound! look at this site Cargando... Whirlpool Ice Maker Reset Button PartSelect 1.003.557 visualizaciones 4:14 Refrigerator Ice Dispenser Chute Door (part #WP2180353)-How To Replace - Duración: 6:38. Whirlpool In Door Ice Maker Not Working Switch to another language: Catalan | Basque | Galician | View all Cerrar Sí, quiero conservarla.

Reply Mike Posted on August 8, 2015 To add to my efforts, the ice maker worked for a day or so. his comment is here Whirlpool icemaker repair is easy and with help from this Whirlpool icemaker repair guide you will repair you icemaker yourself and save expensive repair bills. When the ice level drops below the beam, the control board signals the ice maker to make more ice. It would of been much quicker but I couldn't disconnect the dang wire harness! Kitchenaid Ice Maker Sensor

Disconnect the wire harness on the back side and then remove the two Phillips screws to release the receiver control board from the housing.  Re-install the receiver board in the reverse Categories Annoucements (9) Dishwasher (4) Dryer (12) Freezer (3) Ice Maker (5) Microwave (2) Range/Oven (5) Refrigerator (16) Washer (17) Archives November 2016(1) July 2016(1) May 2016(1) March 2016(2) December 2015(2) Return From Whirlpool Icemaker Repair Guide Appliance-repair-it.com is a free service but it cost to keep it up and running. http://codebuz.com/ice-maker/whirlpool-gold-infrared-ice-maker-not-working.html You assume all responsibilities by purchasing any of the offered fixes.

This switch activates the refrigerator light when the door is open. $10.79 Quantity: In Stock › Suggested tools Air Filter RepairClinic Item #1554868 $13.08 Same Day Shipping Order by 8:00 PM Whirlpool Ice Maker Control Board The feeler arm is the metal wire that stops the icemaker when the ice-bin gets full. Find out more » Total: $44.99 Add to Cart Install Help Watch this helpful video to determine how to install your part.

First, open the freezer and look on the right-hand side and you should see a blinking light.

Any of these instructions may void or limit warranties provided by the manufacturers. Activate the door switch 3 times. In addition to the step by step pictures and details to change those boards, you will to need to get replacement optical boards. Whirlpool W10757851 Common Problem Links | Pre Op | Pre 2002 Diagnostic Tests Post 2002 Diagnostic Tests | Ice Maker Removal | Ice Maker Test Points Ice Maker Parts | Dispenser Parts |

Anyway, I took apart the motor assembly, and sure enough, that white plastic gear was cracked. Duane,Ordered the part from you and received it in timely fashion - thank you. Leave the door closed to let the freezer cool back down and it should start making ice in the next 2-6 hours if it is working properly. navigate here And yes, I already know that I should be just purchased a new ice maker to begin with as the emitter did appear operational beforehand.

How To Test The Whirlpool Ice Maker Optic Control Boards W10757851 First, open the freezer door and look at the status LED on the right hand side. My questions is which control boards or power supply board control the left side of the fridge. Using the jumper wire on the models with the ice-bin mounted in the door is not as effective as with models that have the ice-bin mounted in the freezer compartment such To check this first, disconnect power from the refrigerator then slide the icemaker out without unplugging it and remove the cover off the front of the icemaker.

Open the freezer door and observe the red status light next to the ice maker’s on/off switch. You will not be able to visually see any light coming from the optics boards since it is infrared light (not visible to the human eye). If the optics boards test good, then I would guess your ice maker is bad since it has ice in the tray.