The ice make will fill when the fingers that scoop the ice out are pointing straight up. There is an emitter control board that sends out an infrared beam, and a receiver board that receives the infrared beam. If so , then replace the water valve and turn the freezer temp down slightly . The reason is that there were two different types of optical boards used in these refrigerators. http://codebuz.com/ice-maker/whirlpool-ice-maker-not-working-red-light-blinking.html
Help! Just doesn't make any ice. Vice President: An expert whose answer got voted for 100 times. Open the freezer door (make sure that the freezer door has been closed for a minimum of 10 seconds prior to opening the door).
So I ordered new optics boards. That is why you should perform the diagnostic tests that we list to see if they are functioning properly. Posted on Nov 07, 2007 Helpful 27 Not Helpful 2 Comments Flag rdoran Oct 04, 2010 my optics seem to be fine, because they do what you say they should do.
Post 2002 Diagnostic Tests: Note: The ice bin must be installed on the door to activate the left side flap, ice should not be over the top notches of the bin. Step 4. I called the Sears Tech line and was only able to make an appointment for a repair visit, $74.00 just to show up, any work on the appliance or parts was Kitchenaid Ice Maker Blinking Red Light Regarding a Whirlpool side-by-side can someone tell me what the red light means (regrding the red light in the freezer that remans solid when you hold the flipper door down and
It is a very easy and quick fix...if you can determine from the instructions above that your optical boards are bad, then you will have no problem replacing the optic boards Whirlpool Ice Maker Reset Button If optics are ok then you most likely have a broken motor module on the icemaker and should replace the icemaker thermostat along with it. do not block light single. You will not be able to visually see any light coming from the optics boards since it is infrared light (not visible to the human eye).
Boards purchased from this link have a 1-year warranty, no questions asked, installed or not! Kitchenaid Superba Ice Maker Not Working It would of been much quicker but I couldn't disconnect the dang wire harness! You should be able to find a year your refrigerator was made on the label just inside the door (towards the top on the right-hand side) as shown in Figure 3 Outside of these instructions it would be hard to find these boards for less than $95 with shipping and they would likely have no warranty or guarantee (I show you other
What could this be? http://www.fixya.com/support/t247500-ice_maker_off_switch_blinking_red_light Sign in Share More Report Need to report the video? Kenmore Ice Maker Red Light Blinking Twice Reply Antonio Posted on April 8, 2015 What was the part you had to replace in addition to the optics? Kitchenaid Fridge Ice Maker Not Making Ice A paper clip works really good for this.4.
Back to Top More You May Also Like... his comment is here If the icemaker dumps the ice ( from water pour ) , then look above the fill cup , and see if the black fill tube is frozen . Now I'm not much of a handyman and the tools you said I needed are pretty much the extent of my entire tool collection. I'm also attaching pictures and instructions to replace the boards. Kenmore Refrigerator Ice Maker Not Making Ice
Board assembly listed above. Its obvious when the water door solenoid energizes. Boards purchased from this link have a 1 Year Return Policy! http://codebuz.com/ice-maker/whirlpool-gold-ice-maker-not-working-red-light.html Board Kit, AP3137510 « Last Edit: January 10, 2008, 12:13:21 PM by AJ » Logged technician VIP Member Member Since: Jul 2007 Posts: 2 Re: How to see if your Whirlpool
Anonymous Nov 03, 2008 Same exact problem for me. Kenmore Bottom Freezer Ice Maker Not Working Put a piece of electrical tape over the jumper as the paper clip will be "hot" with power and could kill you if you touch it.You now have the IR control If your light remains solid RED when you push the flap in, then I have the other repair also available within these instructions.
Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. I noticed that the ice level control beam was not on, as usual, so it was suggested that I unplug the fridge to "reboot" the optical control boards. Where is the PCB located? Kenmore Ice Maker Led Blinking Codes My Whirlpool Gold icemaker will not work after I replaced the filter.
Hope this helps.Please take the time to give this solution a fix ya rating.clarkco Posted on Mar 19, 2009 Helpful 2 Not Helpful Flag You can't post conmments that contain an If holding both at same time should the Led be on or off ? Hold flapper it's constant. navigate here No LEDs present but does blink once indicating that it is in harvest mode.
It seems that when the ice maker is on the freezer section frosts up, and ices over. Open the freezer door and observe the red status light next to the ice maker’s on/off switch. hammydude12345 560,875 views 4:06 199 videos Play all Popular Kenmore & Icemaker videosKenmore - Topic Ice Maker not making or dispensing ice -Level Optics Board-Whirlpool,Kenmore ,KitchenAid # 4389102 - Duration: 8:14. When the ice container fills up with ice, the beam is blocked, and it tells the ice maker to stop filling up with ice.
It's expensive but not hard to do. The valve , is where the wall water line connects to on the refrig Sep 05, 2009 | Whirlpool 25.6 cu. Reply Post a New Comment Cancel reply * * * Notify me of follow-up comments by email. Remove the screws holding the emitter switch to the freezer wall.
It took about 5 minutes to install, and it works like a charm. Making sure not to melt the lines and I even turned off the refrigerator off for a couple hours. Living The Bump Home How to Repair a Kenmore Ice Maker When the Red Light Is Flashing and it Won't Make Ice Related Searches Related Articles How to Change a Lid The laser , is supposed to blink .
See Details Whirlpool WRT519SZDW 19 cu. Step 1. ApplianceVideo.com 112,380 views 11:55 Refrigerator Repair- Replacing the Ice Maker Assembly (Whirlpool Part # 2198597) - Duration: 6:30. Jim McCarthy - [email protected] (remove NOSPAM for valid email address) When Someone Locally Ordered a part for their Ice Maker Repair...Dear Mr.
The optics control boards are replaced as a set, even if only one of the two control boards are bad, both will need to be replaced. Or just drag it here! I went through the debug sheet found in the refrigerator grill 3 times and could not find a problem. If you want to play around some more with this it also works with other infrared remotes, like the tv or vcr remote.If you think your ice maker IR control is
Another Satisfied Customer...Received the motor assembly and installed.